WxS 9800-005
NB-IoT PIR Intelligent sensing terminal of IoT
Product Highlights
ü PIR Intelligent sensing terminal of
IoT
ü Excellent capability to prevent
misreport via built-in filter and power supply rejection to efficiently screen
the interference by other frequencies and insensitive to RF interference
ü Edge calculation and cloud data
processing and analysis
ü Deployed in a cellular topology,
Support service providers, the municipal governments and the enterprises to deploy
public and private IOT networks
ü The sensitivity of NB-IoT module is 129
dBm±1 dB, excellent penetration, the network coverage is 20dB stronger than
GSM, LTE and other networks.
ü Support the communication protocol
frequency band published by the international organization agreement 3GPP.
ü Support two kinds of configuration for
data transmission.Single-tone transmission,15kHz/3.75kHz Subcarrier
interval:25.2kbps(Downlink) , 15.625kbps(Uplink);Multi-tone transmission, 15kHz
Subcarrier interval:25.2kbps(Downlink),54kbps(Uplink)
ü Switch freely between Active/Idle/PSM
modes, and ensure that the un-received data is retransmitted.
ü Support
IPv4/IPv6/UDP/CoAP/LwM2M/Non-IP/DTLS/TCP/MQTT protocol stack.
ü Intelligent terminal provides
multi-function interface (MPI), it can be connected with external analog and
digital quantity sensors. (RS232/RS485 interface is optional.)
ü Integrated internal antenna or
optional external SMA/IPEX antenna.
ü OTA (Over The Air) firmware upgrade,
including to upgrade loader and application images
ü Support wide voltage 5~12V DC input, 5
– 10 years of battery operational life with 2 x AA Li-SOCI2 Battery.
ü IP67 enclosure rating.
Application Architecture
Specifications
|
Wireless
|
|
Sensitivity
|
- 129dBm±1dB
|
|
Frequency band
|
B1 @H-FDD: 2100MHz
B3 @H-FDD: 1800MHz
B8 @H-FDD: 900MHz
B5 @H-FDD: 850MHz
B20 @H-FDD: 800MHz
B28 @H-FDD: 700MHz
|
|
Protocol
|
IPv4 / IPv6 IP/UDP/CoAP/LwM2M/Non-IP/ DTLS/TCP/MQTT
|
|
Distance
|
NLOS（Non-line-of-sight）2km;
|
|
Antenna
|
Integrated internal antenna or external IPEX antenna (SMA)
|
|
Mechanical
|
|
Dimension
|
114mm x 80mm x35mm
The overall height increases with the
increase of sensors.
|
|
Shell IP rating
|
IP67
|
|
Operating
Temperature
|
-40℃to +85℃
|
|
Storage
Temperature
|
-40℃ to +90℃
|
|
Total Weight
|
150g
|
|
Electrical
|
|
Supply Voltage
|
Low power consumption, 3.1V~3.66V; 1or2
Li-SOCI2 Battery; 5VDC optional.
|
Installation Guide
Below diagram
shows the general installation guide for WxS9800, it can be installed on any
flat and solid surface, the lid is contacted with the surface and fixed via 2
self-tapping screws:
Below is the
recommendation of the self-tapping screw and its sizes:
The Sample Application
For perimeter security or
intrusion detection application, it is recommended to install WxS9800-2 at the
entrance of the building (on top of the door inside), on top of the window
inside, or mount in the center of the room ceiling, etc. Below diagrams show
the installation Guide for different scenarios
l Above
the door
l Inside the window at the top of the
l Radix
trichosanthis center
.png)
